一種降低管母線焊接缺陷率專用工具的研制及應用
 

鄭燁，羅宇，葉志堅，王云飛
（湖南省送變電工程公司，湖南 長沙 410007）
 

    摘 要：介紹了一種新型的降低管母線焊接缺陷率專用工具的研制，分析了管母線焊接缺陷率產生的原因。對轉動工具、托架支撐件及托架傳動軸的改進進行了闡述，經在某500 kV 變電站新建工程中應用此新工具進行管母線的焊接，降低了管母線焊接的觀感缺陷率，焊接后的管母線觀感質量好，并取得良好的經濟效益。
    關鍵詞：變電站；管母線；焊接；缺陷率
    中圖分類號：TM645.1⁺1     文獻標識碼：B     文章編號：1007-3175(2017)03-0058-03
 

A Kind of Research and Application of Reducing Defect Rate of Tubular Busbar Welding

 

ZHENG Ye, LUO Yu, YE Zhi-jian, WANG Yun-fei
（Hunan Transmission and Transformation Engineering Company, Changsha 410007, China）
 

    Abstract: Introduction was made to the development of special tool, a new-type of reducing defect rate of tubular busbar welding. This paper analyzed the cause of defect rate of tubular busbar welding and expounded the improved turning tool, bracket supports and bracket shaft. After the new tool was used to weld the tubular busbar in new project of certain 500 kV substation, the impression defect rate of tubular busbar welding was reduced and the impression quality of tubular busbar welding was good, with favourable economic benefit.
    Key words: substation; tubular busbar; welding; defect rate
 

參考文獻
[1] GB 50586—2010 鋁母線焊接工程施工及驗收規范[S].
[2] 武旭平，段臨臨，范紹林. 鋁合金管母線焊接工藝[J]. 金屬加工( 熱加工)，2015(18)：7-8.
[3] 龍會國，龍毅，陳紅冬. 鋁母線焊縫質量情況分析與對策[J]. 焊接技術，2011(5)：14-16.
[4] 劉志文， 鄧晉輝， 朱麗麗.500 kV懸掛式管型母線施工方法改進[J]. 廣東輸電與變電技術，2015(1)：21-22.
[5] 張安志. 侯村500 kV變電站管形母線安裝[J]. 山西電力技術，2014(1)：19-21.